Hyundai / 36 t class
Hyundai R360
Hydraulic systems on this machine, the FLUTEK units that fit them, and the catalogue part numbers behind those units.
Hyundai R360 is listed in our fitment library as a 36 t class excavator. The hydraulic systems we cover on it are main pump K3V180DT / K5V160DTH, swing M5X180CHB, travel FTD48. Below are the FLUTEK units that fit those systems and the catalogue part numbers behind them. Part numbers are catalogue-derived and verified against the manufacturer document before we answer.
At a glance - what fits the Hyundai R360
| System | FLUTEK unit | Parts list | Actions |
|---|---|---|---|
| Main hydraulic pump | K3V180DT / K5V160DTH | K3V180 / K5V200DTH | Quote |
| Swing motor / swing device | M5X180CHB | on request | Quote |
| Travel drive assembly | FTD48 | on request | Quote |
Not sure which pump your machine uses- Send the nameplate photo - the control suffix (DTP / DTH) decides the fitment.
Or just send a photo of the part or the nameplate
Pick the photo here, then attach the same photo in WhatsApp with the machine model - we match it to the catalogue line for this machine and confirm the variant.
No photo chosen yet.
FLUTEK units for Hyundai R360
Where the machine was built in different years or for different markets, more than one unit may fit.
Hydraulic systems on the Hyundai R360
Machine - system - unit - part number. Pick the system you are repairing.
Same-class listing: this machine comes from public model line-ups, and the units below are the ones we supply for its tonnage class. Send the nameplate photo and we confirm shaft, regulator and control variant before dispatch.
Main hydraulic pump
Swing motor / swing device
Travel drive assembly
Shop by series for the Hyundai R360
The units above belong to these FLUTEK series. Each series page carries the catalogue part list for every drawing position, and the machines that take it.
Machines of this brand in the field
Representative photograph of a Hyundai Hyundai R360 machine of this class. It is a licensed editorial image, not our stock and not a picture of Hyundai R360 itself.
Parts for this machine, by component group
Shaft group, rotor group, valve block and casing, servo group, seals - every catalogue line for the pump family used on the Hyundai R360.
Common faults on this machine, and what to check first
The diagnosis guides below start from the symptom, list the checks in the order a workshop should work through them, and say which parts usually solve it. Full index: diagnosis guides.
Hoses burst, seals blow, the gauge needle jumps
Valve and pilot control
Hoses failing in the same place, filters splitting or a gauge needle that jumps are transient problems.
Machine slow or noisy when cold
Oil, filtration and the system as a whole
In low ambient temperatures the oil is the problem, not the pump.
Swing slow, weak or drifting to one side
Swing, travel and drive assemblies
Slewing feels sluggish or refuses to hold a load. Nine times out of ten it is not the whole swing assembly - this is the order to…
Controls sluggish or dead
Valve and pilot control
Pilot pressure moves every control spool. When it is low the whole machine feels tired even with a perfectly healthy main pump.
Proportional pilot control reacts late, in steps, or not at all
Valve and pilot control
Machines with proportional pilot control fail in a characteristic way: the function arrives late, arrives in steps, or does not…
Spools stick or lock when cold
Valve and pilot control
A spool that sticks when cold, or grabs in one position, is telling you about oil cleanliness, varnish or bore damage.
Parts that usually solve them
Catalogue lines from the same families. Search the full library by part number from the parts library.
Order by part number
The parts pages list every catalogue position with its number, quantity per set and the model it belongs to.
How we verify fitment and support the repair
Nameplate-first verification
Your machine model plus the pump or motor nameplate decides the shaft, regulator and control variant. We confirm all three before dispatch - that is where most ordering mistakes come from.
Parts book and catalogue cross-check
Every part number on our pages comes from the FLUTEK catalogue parts tables, with the drawing position number so you can match it to the diagram before ordering.
Back on the job quickly
Single pieces and complete assemblies ship cross-border from Guangzhou by express, air or sea. Send the parts list and we quote price, lead time and freight together.
Editorial images used for illustration; see service standards for the full delivery checklist and image credits.
Send your parts list
Prefer email? Fill this in and we reply within 12 working hours. You can also send photos by email.